Accepts input signals from a variety of vehicle senders.
Divides the sender signal pulses by 2, 4, or 8 by choosing one of the output wires.
Power leads are 3' long and input lead is 8' long, which provides quick and easy installation without consuming wire splices.
Operates with input levels as low as .07 volts peak to peak.
Vibration resistant.
Tamper proof, high impact case is sealed against water, dust and humidity.
Wide operating temerature range.
INPUT SIGNAL: sine or square wave from reed switch, variable reluctance, or generator type sendors.
INPUT SENSITIVITY: Delivers full rated 7 volt output signal from inputs as low as 50 millivolts.
DUTY CYCLE: 7 volt output signals are 50 % duty cycle regardless of input signal.
INPUT IMPEDANCE: High input impedance (47 Kilo Ohms) prevents undesirable loading or interference with sender information.
OPERATING VOLTAGE: Operates from supply voltage of 8 to 15 volts DC.
PROTECTION: Protected against accidental polarity reversal, over voltage application, transient spikes, and spurious interference.
TEMPERATURE RANGE: Operates over a temperature range from - 40 to + 125 degrees Centigrade.
TERMINATIONS All input and output leads are prebonded conductors which maintain much of the flexibility of ordany standard wire without the need for twisting strands and tinning.
Provides an undivided, 1:1 isolated and amplified output of the same frequency as the sender.
Accepts a large variety of input signals from vehicle senders.
Operates at frequencies as low as 0.2 HZ. (Equivalent to one tenth M.P.H. for typical automotive speed senders.)
Operates at input levels as low as .05 volts peak to peak.
Power leads are 3 feet long and input leads are 8 feet long, which provides quick and easy installation without time consuming splicing.
Vibration resistant.
Wide operating temperature range.
Tamper proof, high impact case is sealed against dust and humidity.
INPUT SIGNAL: Sine or square wave from reed switch, variable reluctance, or generator type senders.
INPUT SENSITIVITY: Delivers full rated 7 volt output signal from inputs as low as 50 millivolts.
DUTY CYCLE: 7 volt output signals are 50% duty cycle regardless of input signal.
INPUT IMPEDANCE: High input impedance (47 Kilo Ohms) prevents undesirable loading or interference with sender information.
OPERATING VOLTAGE: Operates from supply voltage of 8 to 15 volts DC.
PROTECTION: Protected against accidental polarity reversal, over voltage application, transient spikes, and spurious interference.
TEMPERATURE RANGE: Operates over a temperature range from -40 degrees to + 125 degrees Centigrade.
TERMINATIONS: All leads are prebonded conductors which maintain much of the flexibility of ordinary standard wire without the need for twisting strands and tinning. Signal leads are noise cancelling twisted pair in vinyl jacket.
OPTIONS: In addition to the single output wire Model 1600-08 two oter options are available. Model 1600-08A offers 2 isolated outputs which are in phase with the input signal. Model 1600-08B offers 3 isolaed outputs.
Accepts input signals from all known vehicle senders.
Provides either an undivided, 1:1, isolated output or an output divided by 2, 4, 8, 16, or 32 selectable by a dip switch.
Operates over a wide voltage supply range (5 V to 32 V).
Operates at extremely low signal frequencies (from 2 HZ).
Requires as little as 40 millivolt input signal to deliver output.
Protected against accidental input power polarity reversal.
Wide ambient temperature operating range.
Vibration resistant.
Power leads come standard at 3 ft. long and sender cable 8 ft. long, which provides quick and easy installation without time consuming splicing.
Provision for wire seals, on cover, to prevent tampering with program switch.
Switchable AC coupled output for applications to instruments that require DC isolated input signals.
INPUT SIGNAL: Any wave form attainable from typical gear tooth, slotted vane, electromagnetic AC generator, hall effect or reed switch senders.
INPUT SENSITIVITY: Delivers full rated 7 volt P-P square output signal from inputs a low as 40 millivolts.
DUTY CYCLE: Essentially 50% duty cycle on all divided outputs.
INPUT IMPEDANCE: Greater than 100,000 Ohms, preventing undesirable loading or interference with sender information.
OPERATING VOLTAGE: Extended range of operating voltages from 5 V to 32 V DC.
PROTECTION: Protected against transient spikes, ignition noise and spurious interference by unique 3 stage filter and protected against accidential polarity reversal.
TEMPERATURE RANGE: Unconditionally stable from -40 degrees C to +85 degrees C.
WIRES: All leads are rugged 18 gauge wire rated at 600 Vand at temperatures to 105 degrees C. Input signal leads are noise cancelling 2 conductor twisted pair in a PVC jacket.
OPTIONS: A single output wire provides conditioned pulses with switch selectable division ratios of : 1; 2; 4; 8; 16; or 32. Also, all outputs can be AC or DC coupled with the same switch. In addition to the single output wire, Model 1800-03 also provides a seperate wire for baising the new hall effect and reed switch senders.
and are not allowed to be used on any other site.